How To Install a Sliding Bolt-On Clear PVC Plastic Strip Curtain

Instructions

  • Push the sliding track brackets over the sliding track and position at intervals of no more than 1.2 metres. 
  • Level the track and brackets before securing to brickwork and concrete with rawl-bolts, to steelwork with high tensile nuts & bolts and to timber with coach screws or large gauge wood screws.
  • Place the roller assembly over the M8 bolt and tighten into position using the washer and nut.
  • Place the rollers no more than 1200mm apart and no more than 200mm in from each end of the track. 
  • Slide the required number of M8 bolts down both sides of the track ready to receive the curtain strips. 
  • Push each pre drilled strip over the bolts with the concave side facing the track. 
  • Hold each strip to the track using the aluminium plate, thread the M8 nuts onto the bolts but do not tighten fully. 
  • Slide the strip to the desired starting place before tightening the nuts. 
  • To achieve 100% overlap each strip must butt up to the next on both sides of the track, for 50% overlap each strip should be placed at a distance from each other that it overlaps by a quarter of the width of each strip.
  • Fix an M8 nut and bolt through the side and at each end of the sliding track to stop the track from sliding out.

How To Install a Bolt-On Soffit Fit Clear PVC Plastic Strip Curtain

Instructions

  • Slide the M8 nuts into the centre slot and along the track. 
  • Place the brackets over the M8 nuts and tighten into position using the countersunk bolts. 
  • Place the brackets no more than 1200mm apart and no more than 200mm in from each end of the track. 
  • The ‘L’ shapes brackets should be arranged so that each alternate bracket is facing the opposite side of the track. 
  • Slide the required number of M8 bolts down both sides of the track ready to receive the curtain strips. 
  • Secure the brackets with track attached to the brickwork and concrete with rawl-bolts to steelwork with high tensile nuts and bolts and to timber with coach screws or large gauge wood screws. 
  • Push each pre drilled strip over the bolts with the concave side facing the track. 
  • Hold each strip to the track using the aluminium plate, thread the M8 nuts onto the bolts but do not tighten fully. 
  • Slide the strip to the desired starting place before tightening the nuts. 
  • If you are including Red warning strips remember to position these first. 
  • To achieve 100% overlap each strip must butt up to the next on both sides of the track, for 50% overlap each strip should be placed at a distance from each other that it overlaps by a quarter of the width of each strip. 
  • Finally trim the bottom of each strip to the desired length using a sharp knife.

How To Install a Bolt-On Face Fit Clear PVC Plastic Strip Curtain

Instructions

  • Slide the M8 bolts into the centre slot and along the track.
  • The “L” shaped bracket can be used in any configuration that best suits your requirement.
  • Place the bracket over the M8 bolt and tighten into position using the washer and nut.
  • Place the brackets no more than 1200mm apart and no more than 200mm in from each end of the track.
  • Slide the required number of M8 bolts down both sides of the track ready to receive the curtain strips.
  • Secure the brackets with track attached to the brickwork and concrete with rawl-bolts to steelwork with high tensile nuts and bolts and to timber with coach screws or large gauge wood screws.
  • Push each pre drilled strip over the bolts with the concave side facing the track.
  • Hold each strip to the track using the aluminium plate, thread the M8 nuts onto the bolts but do not tighten fully.
  • Slide the strip to the desired starting place before tightening the nuts.
  • If you are including Red warning strips remember to position these first.
  • To achieve 100% overlap each strip must butt up to the next on both sides of the track, for 50% overlap each strip should be placed at a distance from each other that it overlaps by a quarter of the width of each strip.
  • Finally trim the bottom of each strip to the desired length using a sharp knife.

How To Install a Hook On Soffit Fit Clear PVC Plastic Strip Curtain

Instructions

  • Fit the top track to the face of the door frame with 3 wood screws
  • Sandwich the PVC strip between the stainless steel plates – ensuring the concave side faces the small plate
  • Secure the plate to the PVC curtain with the 3 screws provided
  • Hang the PVC strips on the top track at desired overlap
  • The PVC strip curtain is now ready to use

How To Install a Hook On Face Fit Clear PVC Plastic Strip Curtain

Instructions

  • Pellentesque lacus nunc, lacinia non velit et, fermentum fringilla ante. Sed ultrices ullamcorper tellus a mattis. Fusce.
  • Donec non eros luctus, vulputate elit eu, dictum turpis. Donec a enim diam.
  • Suspendisse sit amet nisl at enim varius suscipit ac non leo. Ut ultrices mattis lobortis. Nullam a vehicula est. Cras scelerisque nunc ipsum.
  • Suspendisse sit amet nisl at enim.
  • Nulla at laoreet diam. Duis a condimentum lorem. Interdum et malesuada fames ac ante ipsum primis in faucibus. Fusce luctus interdum scelerisque.